Sewer hose storage on T@B Outback

Has anyone mounted a sewer hose storage tube to the underside of their T@B Outback near the back end?  If so, how far in from the back end did you mount it?  Any pictures available?

I had initially planned to install one along the side of the trailer tongue, but the platform is in the way and I have my spare tire mounted on the tongue.  The only other place I can think to install the tube would be across the tongue in front of the
propane/battery box and the spare tire, but I'd rather have it out of sight.
2017 white/black trim T@B Outback; 2017 white Subaru Outback; Seattle

Comments

  • TabberJohnTabberJohn Posts: 409Member
    2015 T@B Max S (White/Silver) -> 2014 Ford Escape 2.0L (turbo, AWD, factory tow)
  • AussieAussie Posts: 114Member
    I found that discussion as well,  but the options won't work with my setup.
    2017 white/black trim T@B Outback; 2017 white Subaru Outback; Seattle
  • NomadNomad Posts: 7,341Member
    You probably need to explain your setup then. The two most common external spots are frame and rear.


  • TabberJohnTabberJohn Posts: 409Member
    I think you could mount a PVC tube pretty much anywhere between the back bumper and the brace where the shell attaches to the frame (where Lil_Lucy did).
    The difference is you'd have to drill through the shell to attach tube brackets and place extra large washers on the inside of the shell to spread the load.
    If an Outback is similar to a Max S there is plenty of space along that slope to mount a tube.  You can determine best location for the holes if you remove the rear shelf and reflective baffle and reach down along the back side. You'll likely be inserting bolt and washer blindly depending on how low you want to go.
    The shell is plenty strong enough to do this and silicon sealant would waterproof the mod (like the holes drilled for lights). Doing it blindly won't be fun though.

     
    2015 T@B Max S (White/Silver) -> 2014 Ford Escape 2.0L (turbo, AWD, factory tow)
  • ScottGScottG Posts: 1,548Moderator
    edited November 2016
    TabberJohn, I thought your suggestion in another thread (http://www.tab-rv.com/forum#/discussion/comment/53596) could be an elegant solution for sewer hose storage. As marknjudy pointed out, that dead space in the tail isn't really earning its keep.

    I'd be inclined to pass the pipe all the way through and cap both ends. You'd need enough clearance to avoid cutting into any cabin frame elements or other hard parts. I'd consider this an advanced project, but there are some capable fabricators here who I'm sure could pull it off if there is enough room to do so.
    2015 T@B S
  • marknjudymarknjudy Posts: 353Member
    Hey! Great idea!! Mod is back on the table! Thanks, ScottG!
    Mark - 2016 T@b Max S (Silver/Red), 2012 F-150
  • DalehelmanDalehelman Posts: 1,135Member
    This worked for me.
    1. Hash  T@B Fun
  • TabberJohnTabberJohn Posts: 409Member
    That's the ticket. Was this a no-drill solution?
    I see the zip ties but what are they attached to and how were those anchors attached to the shell?
    2015 T@B Max S (White/Silver) -> 2014 Ford Escape 2.0L (turbo, AWD, factory tow)
  • DalehelmanDalehelman Posts: 1,135Member
    Zip ties were just temporary. Four 1/4" bolts with fender washers. Very easy no big deal.
    1. Hash  T@B Fun
  • Lil_LucyLil_Lucy Posts: 40Member
    I think you could mount a PVC tube pretty much anywhere between the back bumper and the brace where the shell attaches to the frame (where Lil_Lucy did).
    The difference is you'd have to drill through the shell to attach tube brackets and place extra large washers on the inside of the shell to spread the load.
    If an Outback is similar to a Max S there is plenty of space along that slope to mount a tube.  You can determine best location for the holes if you remove the rear shelf and reflective baffle and reach down along the back side. You'll likely be inserting bolt and washer blindly depending on how low you want to go.
    The shell is plenty strong enough to do this and silicon sealant would waterproof the mod (like the holes drilled for lights). Doing it blindly won't be fun though.

     
    Just to clear things up a little, there was no drilling into the shell when mounting my rear sewer hose carrier. It is bolted to a bracket I designed and had made and fits on the spare tire bracket underneath. The 46" sewer hose carrier can be purchased at Camping World or Amazon. (it holds a 10 foot sewer hose). I have the same sewer hose carrier mounted in front to the frame (with 7" hose clamps) for an additional 10 foot of hose if I should ever need it. I don't know if there is a difference between the Outback Model and the Max S in that rear area. I wouldn't think there is.
    I hope the attached pictures explains it better.



    2016 T@b Max-S (Silver/Red Trim) / TV: 2016 Ford Escape
    "Growing old is mandatory. Growing up is optional."
  • TwojgramsTwojgrams Posts: 534Associate Member
    Lil_Lucy-since the Outback carries the spare tire on the Yakima up above, that spare tire bracket isn't on the bottom. One could be fabricated though. Yours is a nice solution.
    John, Judi, Guinness & OD
    T@Bit@t 2015 S Max Outback/2006 V8 4Runner 

  • Lil_LucyLil_Lucy Posts: 40Member
    edited November 2016
    Twojgrams said:
    Lil_Lucy-since the Outback carries the spare tire on the Yakima up above, that spare tire bracket isn't on the bottom. One could be fabricated though. Yours is a nice solution.
    Thanks for pointing that out. I apologize to all you Outback owners. However; that bracket design should work with any model that has the spare tire bracket mounted underneath.
    2016 T@b Max-S (Silver/Red Trim) / TV: 2016 Ford Escape
    "Growing old is mandatory. Growing up is optional."
  • SkiCOSkiCO Posts: 19Member
    Just mounted my hose storage on our new Outback.  I like this because it was really easy and did not require any permanent modification.    
  • TwojgramsTwojgrams Posts: 534Associate Member
    Neat! What length hose does it accommodate and how much room is there for more tubing should it be necessary?
    John, Judi, Guinness & OD
    T@Bit@t 2015 S Max Outback/2006 V8 4Runner 

  • AussieAussie Posts: 114Member
    Perfect!!  I walked all around my Outback last week with a sewer hose holder under my arm and couldn't figure out where to put it so I just returned it.  Off to Camping World again tomorrow to buy another one.  What size straps did you purchase?

    Just curious... what is on the right side of the Yakima rack?
    2017 white/black trim T@B Outback; 2017 white Subaru Outback; Seattle
  • SkiCOSkiCO Posts: 19Member
    It telescopes, this is the 33/60 and I have the standard Rhinoflex with the end caps and they fit no problem.  I used 7" straps.  I have the Yakima High Roller bike rack mounted to the right of the rack.  
  • AussieAussie Posts: 114Member
    Thank you, SkiCO
    2017 white/black trim T@B Outback; 2017 white Subaru Outback; Seattle
  • HomebodyatheartHomebodyatheart Posts: 1,107Member
    Ok, just a question. It's my understanding that these hose holders have holes drilled along the bottom for drainage and ventilation. Granted, you rinse your hose each use, but for me, I'd rather not have that dripping down the back of my T@b. Just a thought...
    2017 T@B Max S silver and cherry red, TV 2015 Toyota Highlander L@dybug ("Bug" aka my esc@pe pod), towed by Big Red, or Silver
  • AussieAussie Posts: 114Member
    I don't recall seeing holes on the one I purchased.  Can anyone confirm?
    2017 white/black trim T@B Outback; 2017 white Subaru Outback; Seattle
  • VernaVerna Posts: 4,216Administrator
    The only holes in these hose holders are in the end caps. 
    Verna, Indianapolis, Indiana; 2014 T@B S M@X, white/red, INDIANA  H@@SIER; towed by 2015 Toyota Tacoma V6 TRD 4x4; T@B Administrator
  • SAMSAM Posts: 1,404Member
    Verna,

    What kind of straps did you use to secure your sewer hose?  We bought 14 inch UV resistant ties that we thought we can daisy chain to increase the length.  Also, since the tank valves are on the drivers side, any reason to put the sewer hose holder on the passenger side?
    Sharon and John - Cleveland Heights, Ohio. Blue and Silver 2017 CSS towed by a 2015 Salsa Red Toyota Sienna
  • HomebodyatheartHomebodyatheart Posts: 1,107Member
    :) Thanks @Verna for clarifying. 
    2017 T@B Max S silver and cherry red, TV 2015 Toyota Highlander L@dybug ("Bug" aka my esc@pe pod), towed by Big Red, or Silver
  • VernaVerna Posts: 4,216Administrator

    SAM said:

    Verna,

    What kind of straps did you use to secure your sewer hose?  We bought 14 inch UV resistant ties that we thought we can daisy chain to increase the length.  Also, since the tank valves are on the drivers side, any reason to put the sewer hose holder on the passenger side?


    I used 18" long by 1/4" wide UV resistant tie wraps from Panduit. I have some around the house. The reason to put the sewer hose tube on the passenger side of the tongue is because it won't fit on the driver's side with the black and gray sewer connections. 

    Just unscrew the end while standing on the driver's side, slide the hose out of the tube and let it drop on the ground. Slide it under the tongue to the driver's side, connect and empty tanks. 

    Put the hose hose on the ground, slide to passenger side, put it in the tube, screw the cap in place, take off your rubber gloves, clean your hands, verify everything is put away and go back to having g fun!
    Verna, Indianapolis, Indiana; 2014 T@B S M@X, white/red, INDIANA  H@@SIER; towed by 2015 Toyota Tacoma V6 TRD 4x4; T@B Administrator
  • DaveCDaveC Posts: 23Member
    Did something similar to @SkiCO, but used the Yakama rack to mount the sewer tube.  See http://tab-rv.vanillaforums.com/discussion/5193/2017-outback-storage-and-sewer-hose-mods#latest for details 
    2017 T@B 320 Outback (IdahoTabato) pushing a 2016 Volvo XC90
  • RangergirlRangergirl Posts: 46Member
    Lil_Lucy said:
    I think you could mount a PVC tube pretty much anywhere between the back bumper and the brace where the shell attaches to the frame (where Lil_Lucy did).
    The difference is you'd have to drill through the shell to attach tube brackets and place extra large washers on the inside of the shell to spread the load.
    If an Outback is similar to a Max S there is plenty of space along that slope to mount a tube.  You can determine best location for the holes if you remove the rear shelf and reflective baffle and reach down along the back side. You'll likely be inserting bolt and washer blindly depending on how low you want to go.
    The shell is plenty strong enough to do this and silicon sealant would waterproof the mod (like the holes drilled for lights). Doing it blindly won't be fun though.

     
    Just to clear things up a little, there was no drilling into the shell when mounting my rear sewer hose carrier. It is bolted to a bracket I designed and had made and fits on the spare tire bracket underneath. The 46" sewer hose carrier can be purchased at Camping World or Amazon. (it holds a 10 foot sewer hose). I have the same sewer hose carrier mounted in front to the frame (with 7" hose clamps) for an additional 10 foot of hose if I should ever need it. I don't know if there is a difference between the Outback Model and the Max S in that rear area. I wouldn't think there is.
    I hope the attached pictures explains it better.



    46"? I have one of those fancy hoses (with the elbo) Rhino...something. I laid it out on the ground and scrunched it together as much as possible, but it was 5' long. Do you think it could be shoved into this? Also, could you show a very close up of how you have your tire mounted there? I see the U bolts, but details? I want to mount mine there and am the searching online becomes almost obsessive...you find photos, but not lost of detailed how -to's. Whoever has the corrugated tube..where did you get that? Thanks

  • RangergirlRangergirl Posts: 46Member
    DaveC said:
    Did something similar to @SkiCO, but used the Yakama rack to mount the sewer tube.  See http://tab-rv.vanillaforums.com/discussion/5193/2017-outback-storage-and-sewer-hose-mods#latest for details 
    Would you show a close up of how or what is holding your tire onto the rack? I have a Rhino Rack on my car, but not sure what to use to secure the tire, if I go that route. Thanks.

  • RangergirlRangergirl Posts: 46Member
    Lil_Lucy said:
    I think you could mount a PVC tube pretty much anywhere between the back bumper and the brace where the shell attaches to the frame (where Lil_Lucy did).
    The difference is you'd have to drill through the shell to attach tube brackets and place extra large washers on the inside of the shell to spread the load.
    If an Outback is similar to a Max S there is plenty of space along that slope to mount a tube.  You can determine best location for the holes if you remove the rear shelf and reflective baffle and reach down along the back side. You'll likely be inserting bolt and washer blindly depending on how low you want to go.
    The shell is plenty strong enough to do this and silicon sealant would waterproof the mod (like the holes drilled for lights). Doing it blindly won't be fun though.

     
    Just to clear things up a little, there was no drilling into the shell when mounting my rear sewer hose carrier. It is bolted to a bracket I designed and had made and fits on the spare tire bracket underneath. The 46" sewer hose carrier can be purchased at Camping World or Amazon. (it holds a 10 foot sewer hose). I have the same sewer hose carrier mounted in front to the frame (with 7" hose clamps) for an additional 10 foot of hose if I should ever need it. I don't know if there is a difference between the Outback Model and the Max S in that rear area. I wouldn't think there is.
    I hope the attached pictures explains it better.



    46"? I have one of those fancy hoses (with the elbo) Rhino...something. I laid it out on the ground and scrunched it together as much as possible, but it was 5' long. Do you think it could be shoved into this? Also, could you show a very close up of how you have your tire mounted there? I see the U bolts, but details? I want to mount mine there and am the searching online becomes almost obsessive...you find photos, but not lost of detailed how -to's. Whoever has the corrugated tube..where did you get that? Thanks

    I have the Rhino Flex hose. Will it fit in this tube? The elbow comes off, but the specs don't say the interior diameter.
  • SAMSAM Posts: 1,404Member
    Rangergirl, we purchased the 64 inch Valterra sewer hose holder and the 15 foot Rhino flex that collapses down to 56 inches and mounted it to the passenger side frame.  The hose and connectors fit fine.  We also have an additional 5 feet of hose and connectors, just in case.  
    Sharon and John - Cleveland Heights, Ohio. Blue and Silver 2017 CSS towed by a 2015 Salsa Red Toyota Sienna
  • hymiehymie Posts: 100Member

    This is where we mounted ours. Works great.
    James & Jacquie     Almonte, Ontario
    2016 Jeep Cherokee & 2017 T@B Outback
  • DaveCDaveC Posts: 23Member
    @Rangergirl   Tire mount came with the Outback package.. It bolts to the Yakama rack and has a hasp for a lock.  Might check Yakama.  My sewer hose carrier holds 10 and 5 foot Rhinos plus the elbow (disconnected).
    2017 T@B 320 Outback (IdahoTabato) pushing a 2016 Volvo XC90
Sign In or Register to comment.